Tc-helicon VoiceTone Double Manual do Utilizador Página 1

PRODUCT MANUALENGLISH VERSION

You can use two or three VoiceTone pedals in series.Theconnection order is important:o VoiceTone Correct should be connected beforeDoubleo VoiceTone

121. Input KnobControls the microphone pre-amplifier gain. Double canaccept dynamic or condenser microphones.2. Input LightIndicates the input level o

136. 48 Volt Phantom Power LightIndicates phantom power on or off.7. Bank Select SwitchesPush to cycle up and down through the 10 banks.8. Stereo Ligh

14Phantom PowerBefore using any setup configuration, determine the typeof microphone you are using:Dynamic microphone: phantom power off.Condenser mic

3. Connect Double's power adapter to main powerand to the Power Input on Double.15Standard Live SetupThe standard live setup for VoiceTone Double

16Stereo SetupIf you run your sound system in stereo, or you arerecording in a studio, you can enable stereo mode. In thissetup, effect patches have m

17Mono Sound Engineer SetupIf you are in a situation where a live sound engineermixes your vocal sound, you have the option of givingthem control over

Stereo Sound Engineer SetupIn a live stereo PA setup or a recording studio you canmute your dry voice while the outputs produce %100wet stereo for eas

19If the Pitch and Time controls do not appear to make anaudible change, it’s likely that on the μMod block is usedin that preset. Some presets are ma

Making Adjustments20The Overdub and μMod controls act like a mixer to varythe relationship between the two effects blocks.OverdubThis controls the lev

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4QuickStart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

21Patch ListBank Name Bank Number Patch 1 Patch 2 Patch 3Showcase 0 Mono Overdub 4V Porta Detune Oct Down StereoMicroshift 1 E Type McrShift Sweet Cho

22The following lists rough descriptions for eachpreset. Any mention of pan position is invalid whenDouble is set to the default mono output mode. Mon

23Patch List DescriptionsMale Octaves - 4 voices with detuning, male gender.Additional μMod detuning is added to both the overduband dry voices.Female

24FAQ & Troubleshooting:1. I'm not getting any sound out of Doublea. Confirm the power adapter is properly connectedby checking that a patch

effect on, and the Input Light is never flashing red, tryreducing the μMod and Overdub levels for the currentpatch.b. If Double’s Input never flashes

26SpecificationsAnalog Inputs Connectors Balanced XLR, Input Impedance 1kOhm  Mic Input Sensitivity @ 0dBFS -44dBu to +2dBu  Mic Input Sensitivity

4Welcome to VoiceTone DoubleVoiceTone Double was built for the performanceminded singer desiring studio quality doubling andthickening on stage.The ef

5About TC-HeliconAt TC-Helicon we truly believe that the voice is theworld's most beautiful instrument. We don't mean todegrade other beauti

6Step 1:Connect your microphone to a mic cableStep 2:Connect the mic cable to the Mic Input on DoubleQuick StartMake sure Double is not powered.NOTE:

7Step 3:Connect a mic cable to the Left (mono) Output ofDouble.Step 4:Connect the mic cable from Double to a mic input onyour sound system.Quick Start

8Step 5:Set the Input Knob fully left.Step 6:Connect Double's power adapter to main power and tothe Power Input on Double.Quick Start

9Step 7:While singing through your microphone, raise the InputKnob until the Input Light turns green, sometimesorange on louder parts, but never red.S

10Step 9:You're ready to add doubling effects to your voice!a. Turn the effect on or off with the On (right)Footswitch.b. Listen to different pat